PIC16F873T-04E/SO【PDF 12/218 页】IC MCU FLASH 4KX14 EE 28SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3889

8页 9页 10页 11页 [12页]13页 14页 15页 16页

2001 Microchip Technology Inc.

DS30292C-page 107

PIC16F87X

10.3.2

USART SYNCHRONOUS MASTER

RECEPTION

Once synchronous mode is selected, reception is

enabled

setting

either

enable

bit

SREN

(RCSTA<5>), or enable bit CREN (RCSTA<4>). Data is

sampled on the RC7/RX/DT pin on the falling edge of

the clock. If enable bit SREN is set, then only a single

word is received. If enable bit CREN is set, the recep-

tion is continuous until CREN is cleared. If both bits are

set, CREN takes precedence. After clocking the last bit,

the received data in the Receive Shift Register (RSR)

is transferred to the RCREG register (if it is empty).

When the transfer is complete, interrupt flag bit RCIF

(PIR1<5>) is set. The actual interrupt can be enabled/

disabled

setting/clearing

enable

bit

RCIE

(PIE1<5>). Flag bit RCIF is a read only bit, which is

reset by the hardware. In this case, it is reset when the

RCREG register has been read and is empty. The

RCREG is a double buffered register (i.e., it is a two

deep FIFO). It is possible for two bytes of data to be

received and transferred to the RCREG FIFO and a

third byte to begin shifting into the RSR register. On the

clocking of the last bit of the third byte, if the RCREG

(RCSTA<1>) is set. The word in the RSR will be lost.

The RCREG register can be read twice to retrieve the

two bytes in the FIFO. Bit OERR has to be cleared in

software (by clearing bit CREN). If bit OERR is set,

transfers from the RSR to the RCREG are inhibited, so

it is essential to clear bit OERR if it is set. The ninth

receive bit is buffered the same way as the receive

data. Reading the RCREG register will load bit RX9D

with a new value, therefore, it is essential for the user

to read the RCSTA register before reading RCREG in

order not to lose the old RX9D information.

When setting up a Synchronous Master Reception:

Initialize the SPBRG register for the appropriate

baud rate (Section 10.1).

Enable the synchronous master serial port by

setting bits SYNC, SPEN and CSRC.

Ensure bits CREN and SREN are clear.

If interrupts are desired, then set enable bit

RCIE.

If 9-bit reception is desired, then set bit RX9.

If a single reception is required, set bit SREN.

For continuous reception, set bit CREN.

Interrupt flag bit RCIF will be set when reception

is complete and an interrupt will be generated if

enable bit RCIE was set.

Read the RCSTA register to get the ninth bit (if

enabled) and determine if any error occurred

during reception.

Read the 8-bit received data by reading the

RCREG register.

10. If any error occurred, clear the error by clearing

bit CREN.

11. If using interrupts, ensure that GIE and PEIE

(bits 7 and 6) of the INTCON register are set.

TABLE 10-9:

REGISTERS ASSOCIATED WITH SYNCHRONOUS MASTER RECEPTION

Address

Name

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

Value on:

POR,

BOR

Value on all

other

RESETS

0Bh, 8Bh,

10Bh,18Bh

INTCON

GIE

PEIE

T0IE

INTE

RBIE

T0IF

INTF

R0IF

0000 000x

0000 000u

0Ch

PIR1

PSPIF(1)

ADIF

RCIF

TXIF

SSPIF

CCP1IF

TMR2IF

TMR1IF

0000 0000

18h

RCSTA

SPEN

RX9

SREN

CREN

—

FERR

OERR

RX9D

0000 -00x

1Ah

RCREG

USART Receive Register

0000 0000

8Ch

PIE1

PSPIE(1)

ADIE

RCIE

TXIE

SSPIE

CCP1IE

TMR2IE

TMR1IE

0000 0000

98h

TXSTA

CSRC

TX9

TXEN

SYNC

—

BRGH

TRMT

TX9D

0000 -010

99h

SPBRG

Baud Rate Generator Register

0000 0000

Legend: x = unknown, - = unimplemented, read as '0'. Shaded cells are not used for synchronous master reception.

Note

Bits PSPIE and PSPIF are reserved on PIC16F873/876 devices; always maintain these bits clear.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式